- Hp smart array p410i manual driver#
- Hp smart array p410i manual manual#
- Hp smart array p410i manual Offline#
The website is available under the terms of the GPL-3.0
Hp smart array p410i manual manual#
Using mandoc for the conversion of manual pages. Package information: Package name: core/man-pages Version: 5.13-1 Upstream: Licenses: GPL, custom Manuals: /listing/core/man-pages/ Table of contents Aĭescription of the project, information about reporting bugs, and the latest This page is part of release 5.13 of the Linux man-pages project. SEE ALSO cciss(4), sd(4), st(4), cciss_vol_status(8),ĭocumentation/ABI/testing/sysfs-bus-pci-devices-cciss in the Linux These are used extensively by the HP ArrayĬonfiguration Utility, SNMP storage agents, and so on.
Hp smart array p410i manual driver#
CCISS_GETDRIVVER Returns driver version in three bytes encoded as: (major_version << 16) | (minor_version << 8) |ĬCISS_PASSTHRU, CCISS_BIG_PASSTHRU Allows "BMIC" and "CISS" commands to be passed through CCISS_GETPCIINFO Returns PCI domain, bus, device, and function and "board ID"
Writing to the hpsa-specific host "rescan" attribute. Ioctls are described in the Linux kernel source fileĬCISS_DEREGDISK, CCISS_REGNEWDISK, CCISS_REGNEWD These three ioctls all do exactly the same thing, which is to cause theĭriver to rescan for new devices. Many, but not all of the ioctls supported by the cciss(4) driver areĪlso supported by the hpsa driver. Logical drive or physical device can be addressed.Ĭ: b: t: l are the controller, bus, target, andįor example: # cd /sys/class/scsi_disk/4:0:0:0/deviceįor compatibility with applications written for the cciss(4) driver, sys/class/scsi_disk/c:b:t:l/device/lunid This attribute contains the 16 hex-digit (8 byte) LUN ID by which a For example: # cd /sys/class/scsi_disk/4:0:0:0/device sys/class/scsi_disk/c:b:t:l/device/raid_level This attribute contains the RAID level of each logical drive. HPSA-specific disk attribute files in /sys /sys/class/scsi_disk/c:b:t:l/device/unique_id This attribute contains a 32 hex-digit unique ID for each logicalĭrive. For example: # cd /sys/class/scsi_host/host4 sys/class/scsi_host/host*/firmware_revision This attribute contains the firmware version of the Smart Array. Useful when hot plugging devices like tape drives, or entire storage boxesĬontaining preconfigured logical drives.
User should not normally have to use this attribute. GUI or the command-line variety) thus, for logical drive changes, the Triggered automatically by HP's Array Configuration Utility (either the Notify the SCSI midlayer of any changes detected. Tape drives, or newly configured or deleted logical drives, etc.) and Writing to this attribute will cause theĭriver to scan for new, changed, or removed devices (e.g., hot-plugged HPSA-specific host attribute files in /sys /sys/class/scsi_host/host*/rescan This is a write-only attribute. Generic driver ( sg(4)), with device nodes named /dev/sd*, Via the SCSI tape driver ( st(4)), and the RAID controller via the SCSI Logical drives are accessed via the SCSI disk driver ( sd(4)), tape drives
Hp smart array p410i manual Offline#
(either hpacuxe(8) or hpacucli(8)) or the Offline ROM-basedĬonfiguration Utility (ORCA) run from the Smart Array's option ROM at boot
To configure HP Smart Array controllers, use the HP Array Configuration Utility Since Linux 4.14, the following Smart Array boards are also The hpsa driver supports the following Smart Array boards: Supported with hpsa, and cciss(4) should still be used for These older boards have not been tested and are not Hpsa to drive older controllers that would normally be handled by theĬciss(4) driver. That predates the RAID controller, though it may also be used to enable Typically this is used to allow installation of operating systems from media This allows newer hardware to work with older drivers. Options hpsa_allow_any=1: This option allows the driver to attempt to operate onĪny HP Smart Array hardware RAID controller, even if it is not explicitly SYNOPSIS modprobe hpsa DESCRIPTION hpsa is a SCSI driver for HP Smart Array RAID controllers.
0 kommentar(er)
